LD Cfl/tl Ballast Driver Preheat And Dimming. HIGH VOLTAGE RAIL TO V dV/dt IMMUNITY ± 50 V/ns IN FULL TEMPERATURE RANGE DRIVER. LD IC BALLAST DRIVER CFL/TL SO STMicroelectronics datasheet pdf data sheet FREE from Datasheet (data sheet) search for. LD datasheet, LD circuit, LD data sheet: STMICROELECTRONICS – CFL/TL BALLAST DRIVER PREHEAT AND DIMMING,alldatasheet.

Author: Kajilabar Akinogul
Country: Italy
Language: English (Spanish)
Genre: Music
Published (Last): 28 February 2011
Pages: 214
PDF File Size: 17.87 Mb
ePub File Size: 10.77 Mb
ISBN: 270-1-17723-354-3
Downloads: 65053
Price: Free* [*Free Regsitration Required]
Uploader: Mikora

Figure 19 shows us the voltage and current measurement at Ton equal to 3 ms. Main components Current Controller For Stepping Motors High-voltage half bridge driver DN Design note A high power stepper motor driver Designs from our labs describe tested circuit designs from ST labs which provide optimized solutions for specific applications. Precision ma regulators. ,6574d

For the resonant circuit, Lr and Cr are the main parameters. At t2, il1 reaches zero, and l6574x linearly increases to the negative peak by the voltage across Cf2. Heptawatt package Power amplifier Flyback generator Stand-by control Output current up to 3.

CFL/TL Ballast Driver Preheat And Dimming

Push-pull four channel driver with diodes. Power factor in operating range Figure High voltage fast-switching NPN power transistor. Compared to the formal CFL solution, this solution not only provides energy savings, but also higher reliability and a much longer operating life.

The main applications are gas lighters or ignitors More information. User manual pin smartcard interface STP demonstration board Introduction The purpose of this document is to describe, and provide information on, how to efficiently use the STP smartcard interface. Although the glitch was there, due to the limitation of maximum Ton, the power factor is always higher than 0.

L1 current shape The overall current flow shape in L1 during one half AC line cycle is shown in Figure 9. The capacitor C according to the relations: You could imagine a multitude of applications More information. In addition, a circuit detects the firing angle of the triac and adjusts lamp power by adjusting the switching frequency of the half bridge to control lamp power depending on the position of the triac dimmer. White LED power supply for large display backlight.


LD Datasheet PDF – STMicroelectronics

The additional features of TDAvery low number of external. EN2 input active high restarts the start-up procedure preheating and ignition sequence. With the implementation of the PFC solution, the lamp power can be adjusted by switching the frequency of the driver circuit that corresponds to the illumination level set by the triac dimmer. Application note An MCU-based low cost non-inverting buck-boost converter for battery chargers Introduction As the demand for rechargeable batteries increases, so does the demand for battery chargers.

Low-power quad voltage comparator. Three phase motor driver. Full load efficiency vs. Please refer to Figure 16 below.

LD Datasheet pdf – CFL/TL BALLAST DRIVER PREHEAT AND DIMMING – SGS Thomson Microelectronics

The triac shuts down when the current is less than the holding current. The tags and reader s antennas. The half AC line cycle of sinuous xatasheet and firing angle Figure 6. The main applications are gas lighters or ignitors. Three terminal adjustable current sources Features Operates from 1V to 40V 0. It is clear that the boost inductor current flows in two directions and the PFC circuit works at boundary conduction mode.

Thus the voltage across C1 is always higher than the line peak.

L6574D PDF Datasheet浏览和下载

For more information More information. Description High voltage fast-switching NPN power transistor Datasheet production data Features Low spread of dynamic parameters Minimum lot-to-lot spread for reliable operation Very high switching speed Applications More information. Download datasheet Kb Share this page. In this solution, the dimming function is obtained using two methods: Information in this document supersedes and replaces all information previously supplied.

Application note IEC standard testing Introduction This Application note is addressed to technical engineers and designers to explain how STMicroelectronics protection devices are tested according. The triac can be triggered at any timing of the sinuous voltage AC line inputand can be kept in conduction state until reaching zero line voltage. In each More information. EnFilm – rechargeable solid state lithium thin film battery Applications Datasheet production data Device is intended to be used in datasheett wide range of applications including: Internet of things Sensors and More information.


Triac turn-on time vs. At t4, il1 reaches zero, where the new switching cycle begins. Typical datssheet Figure 2.

If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such dataaheet party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

Because bus voltage the voltage across the storage capacitor falls, the system stops operating at an angle less than Transil, transient voltage surge suppressor diode for ESD protection. The figures also show the negative resistance characteristics of the lamp, such as when the lamp current decreases, the voltage increases accordingly. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of l65744d ST products and services described herein.

AC line input Figure The equivalent resistance between Pin 4 and GND of the IC decreases, so the switching frequency increases, hence lamp power decreases. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics