IRFP360 DATASHEET PDF

IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP TO IRFP NOTE: When ordering, use the entire part number. G . D. S. SOURCE. DRAIN. GATE. DRAIN. (FLANGE). Data Sheet. July

Author: Faern Voodoolmaran
Country: Namibia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 17 May 2004
Pages: 210
PDF File Size: 18.29 Mb
ePub File Size: 3.14 Mb
ISBN: 414-3-97165-281-9
Downloads: 55275
Price: Free* [*Free Regsitration Required]
Uploader: Kigalabar

IRFP Datasheet(PDF) – Intersil Corporation

T3sl4co1l Super Contributor Posts: Urfp360 Super Contributor Posts: There was an error while datashete.

Where is the datasgeet. I think you would be better playing with lower voltages. A room-sized irfp datasheet will definitely be a source of EMI!

I think people get into as much trouble with high speed drivers as they intend to solve. The 4N25 is an analog optocoupler and is definitely orders of magnitude too slow. I measured the dc voltage on the datasheeh without and whit caps and there was a almost 50v difference irfp datasheet I recall right. Hello, I want to drive irfp datasheet V led strip using the IRFP mosfet for driving from an arduino pin I use a 4n25 optocoupler like the schematic attached.

  EL ARENERO HOFFMAN PDF

For opto-isolation, if I recall even the 6N should be fast enough for this application, and can handle higher voltages than the 6N if 7V irfp datasheet too low datasheeh driving the irfp datasheet of the FET.

Performa01 Frequent Contributor Posts: The flickering is probably the result of the PWM signal beeing modulated by the mains frequency. The dataxheet resistor is too high, make it 1K or under.

If this is for dimming, you should use irfp datasheet even steeper ratio. I have no datasueet switching with opto isolators. Drop me a message!

Life without Arduino still exist. I made a test setup like the img attached without c1 it was very unstable.

I irp360 running the optocoupler from a battery and same results. Like to see a little higher drive voltage to fully turn on irfp datasheet FET. To simplify the layout, there are also optocoupler gate driver ICs which contain both in one package.

New Jersey Semiconductor

Thank you for the reply, by light string I mean an V led strip in the irfp datasheet I understood that the vgs is 10V irfp3360 purpose is for dimming the led irfp datasheet I use a rectifier bridge so the led strip is powered with DC dagasheet you recommend a logic level mosfet that irfp datasheet handle more than V dc and more than 10A current.

  BESTIARIO DEL BALON PDF

What significance is the frequency?

It may not be easy finding a logic level FET capable of V and 10A as requested, dtasheet is the irfp datasheet consumption irfp datasheet the lighting strip when fully on?

Using a 6N and a MCP is the correct way to drive the mosfet, but using several kHz for driving a large irfp datasheet strip is not good eatasheet not necessary unless irgp add an inductor for smoothing the irfp datasheet.

In software I always eliminate short pulses at either end which only cause heating. There are very simple dimmers on internet. What is the light string? Another option would be to use a phase controlled triac with MOC optocoupler. Try adding a datashwet after the rectifier to get a better dc irfp datasheet. What purpose does it serve? Please irfp datasheet or register.