Manufacturer Part No: HCNRE. Order Code: Technical Datasheet: HCNRE Datasheet. See all Technical Docs. Broadcom HCNRE: available from 15 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and . HCNR/HCNR is UL Recognized with Vrms for 1 minute per UL . Mount. Wing & Reel 1 Minute rating VIORM = Vpeak. Quantity. E.
|Published (Last):||4 July 2005|
|PDF File Size:||8.75 Mb|
|ePub File Size:||11.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Pins 1, 2, 3, and 4 shorted together and pins hvnr201-000e, 6, 7, and 8 shorted together. Example Application Circuits The circuit shown in Figure 16 is a high-speed low-cost circuit designed for use in the feedback path of switchmode power supplies.
HCNRE Avago Technologies US Inc., HCNRE Datasheet
As a result, the non-linearity. Example Application Circuits The circuit shown HCNR fig 2 0. Two example circuits that operate with bipolar input signals are discussed in the next section. Of Pins 8 Forward Voltage 1. Diodes D1 and Datsaheet help reduce crossover distortion by keeping both amplifiers active during both positive and negative portions of the input signal. Units Test Conditions Fig. The input terminals of the op-amps and the photodiodes are connected in the circuit using Kelvin connections to help ensure the accuracy of the circuit.
Option datasheets are available. Specific performance will depend on circuit topology and components. An analysis similar to the one above yields the following expression relating output current to input voltage: The relationship between the input optical power and the output current of a photodiode is very linear.
Contact your Avago sales representative or authorized distributor for information. The first circuit has the obvious advantage of requiring only one optocoupler; however, the offset performance of the circuit is dependent on the matching of IOS1 and IOS2 and is also dependent on the gain of the optocoupler.
Datashet Creepage L IO2 The output photodiode then converts the stable, linear light output of the LED into a current, which can then be converted back into a voltage by another amplifier. The fi nal circuit shown in Figure 19 isolates a bipolar analog signal using only one optocoupler and generates two output signals: It is also possible to convert this circuit into a fully bipolar circuit with a xatasheet output signal by using the output of the 6N to drive some CMOS switches to switch the polarity of PD2 depending on the polarity of the input signal, obtaining a bipolar output voltage swing.
The lower gains, higher input currents and higher offset voltages affect the accuracy of the circuit, but not the way it operates.
CNR fig 8 All other trademarks are the property of their respective owners. The circuit operates in the same manner as well; the only difference is the performance of amplifiers A1 and A2.
Loop-powered mA current loop circuits. This would reduce the ycnr201-000e gain of the input circuit, reducing circuit accuracy and bandwidth.
IPD2 error to best fit line is the deviation below and above the best fit line, expressed as a percentage of the full scale output.
Elcodis is a trademark of Elcodis Company Ltd.
Normally the forward voltage drops of the diodes would cause a serious linearity or accuracy problem. LED input current vs. And R7 is selected so that Q4 operates at about the same collector current as Q2. The two OP-AMPS shown are two separate LM, and not two channels in a single dual package, otherwise the loop side and output side will not be properly isolated. In the high-speed circuit discussed above, the input and output circuits are stabilized by reducing the local loop gains of the input and output circuits.
It’s a community-based project which helps to repair anything. Figure 13 illustrates how to change the basic circuit to accommodate both positive and negative input and output voltages. External Clearance L IO1 9. The feedback amplifier acts to stabilize and linearize the light output of the LED.
IORM peak Example 2: A Parameter Symbol Input-Output Also notice that IPD1 is exactly proportional to VIN, giving a very linear relationship between the input voltage and the photodiode current. The output photodiode produces a photocur rent. IPD1 is equal to the current in R1 and is given by the following equation: Typical photodiode leakage vs.
Protective cut-out switches must be used to ensure that the safety limits are not exceeded.
These capacitors also limit the bandwidth of the circuit to about 10 kHz and can be used to reduce the output noise of the circuit by reducing its bandwidth even further. However, an additional amplifier is used to provide an appropriate offset voltage to the hcn2r01-000e amplifiers that exactly cancels the diode voltage drops to maintain circuit accuracy.
Data Sheet HCNR200 and HCNR201 High-Linearity Analog Optocouplers
It is advised that normal chnr201-000e precautions be taken in handling and assembly. High Speed High Precision 1. The circuit has a bandwidth of about 1.