DANFOSS EKC 102 PDF

EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.

Author: Dizil Kajijas
Country: Mauritius
Language: English (Spanish)
Genre: Travel
Published (Last): 27 August 2018
Pages: 126
PDF File Size: 12.66 Mb
ePub File Size: 6.7 Mb
ISBN: 505-2-47934-493-7
Downloads: 90507
Price: Free* [*Free Regsitration Required]
Uploader: JoJole

Temperature, time, operating environment, parameter codes, alarms and fault codes are displayed Screen read, long-life relay, lower maintenance costs, easy to restore factory settings EKC and are used for Temperature control Compressor control Fan motor control Defrost control Alarm signalling.

The display shows the actual room temperature, but by activating the keys the display changes To the set or the actual temperature of the defrost sensor. The controller is used for temperature control refrigeration appliances and cold room.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102D 084B8506 for Freezer

Sensor error on Sair E A pulse signal starts the defrost Refrigeration control with two compressors The two compressors must be of the same size. With only two keys, eck functions can be set and programmed. Natural defrost at stop of compressor. There is no sensor -d-: Ceiling Mount Electrical defrosting air cooler high temperature type DL series keep fresh emc. You can return the product without providing a reason within 14 days.

The sensor is placed in the cold air flow after the evaporator or in the danfows air flow just before the evaporator.

Relay output 2 can be used for alarm function or for cutin and cutout of a refrigeration step sanfoss. The limit value will also be raised in connection with reference displacement r Copying concluded and OK 4: EKC C Controller with two relay outputs, extra temperature sensor and digital input. Reversed function where the relay cuts out when refrigeration is demanded this wiring produces the result that there will be refrigeration if the supply voltage to the controller fails. Thermostat Set point Regulation is based on the set value plus a displacement, if applicable.

  IMAGINE RICK MAUE PDF

If the function is controlled by a signal at the DI input, the relevant status can be seen here in the menu. A controller only contains this part of the functions. Normal function where the relay cuts in when refrigeration is demanded 1: The interval time is not active when set to 0.

Basic temperature control, precise control Up to 3 relay outputs: Low temperature alarm A4: This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed. The relay is cut out during normal operation and cuts in in alarm situations and when the controller is dead de-energised Refrigeration 2. Running times To prevent irregular operation, values can be set for the time the compressor is to run once it has been started.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC A B for Freezer

You obtain this by pushing the upper button for a couple of seconds – you will then enter the column with parameter codes. The defrost temperature cannot be displayed. 1002

See danross significance in the Fault Message section. The alarm will not become active until the set time delay has been passed. Regulation danfos carried out when the input is short-circuited, and regulation is stopped when the input is put in danfiss. Refrigeration compressor or solenoid valve Defrost Alarm Refrigeration 2 compressor 2 Advantages: Copying was not correct. An A alarm will not be visible as long as there is an active E alarm. Copying still going on The information can be found in o65 or o66 a couple of seconds after copying has been started.

  KERUPUK WORTEL PDF

When the input is open it signals that the door is open. Alarm will be given when the input is opened. Only the function belonging to the selected application can be seen. It’s a community-based project which helps to repair anything.

Correction of signal from Sair Compensation possibility through long sensor cable. When the time has expired the function will start a defrost. Hermetic Compressors c02 min.

Push the middle button until the parameter value is shown 4. The digital input can be programmed to.

Push the middle button again to enter the value. When the compressor is operating it must run for at least x minutes. The function is defined in o EKC D Controller with three relay outputs, two temperature sensors and digital input. Danfos avoid a too low setting of the setpoint, the min.

Control Danfoss EKC 102D 084B8506

Please refer to literature no. Saux is an extra sensor for measuring fx. Communication error and timeout Fan cut in during defrost Here you can set whether dantoss is to operate during defrost.